Megger MFT-X1 EV Test Kit


Sale price£2,200.00
Only 1 unit left


Megger MFT-X1 EVSE Test Kit Expected to ship mid-April 2023

The Megger MFT-X1 EVSE Test Kit comes complete with a Megger MFT X-1 Multifunction Tester and a Megger EVCA210-UK Electrical Vehicle Charger Adaptor. The MFT-X1 is designed to be used on all single or 3 phase domestic, commercial and industrial installations. Capable of performing a wide range of tests including high resolution 0.001Ω loop testing, automatic volt drop measurement, stabilised installation test voltage, configurable RCD and EV test sequence tests. The EVCA210-UK adaptor is an easy to use electrical connector designed to throughly test Mode 3 AC Electric Vehicle charge points.

Megger MFT-X1 Multifunction Tester

The MFT-X1 is suitable for both EV charge point installation testing with RCD Type B or RDC protected charge points. Used alongside the Megger EVCA adaptor, The MFT-X1 can test and maintain all known EV chargers. The Megger MFT-X1 features a high contrast 480 x 272 colour display (with monochrome mode) and an enhanced colour-coded test selection rotary dial for ease of use in all lighting conditions. The MFT-X1 is deigned for the electrical testing of single and 3-phase installations. Using the patented confidence meter True loop measurements can be taken and is fully compatible with CertSuite for easy certificate generation and reporting.

Incorporating a stabilised insulation test voltage to ensure the output voltage is accurate within +/-3% +2 digits. The MFT-X1 provides a highly accurate test voltage without the risk of over voltage damage to circuits and components.

The Megger MFT-X1 can be powered with either the included Megger Li-ION battery pack or using standard NiMH or Alkaline batteries. The rechargeable Li-ION battery can be swapped with the AA carrier module, providing a fast and flexible battery solution. The IP54 housing and CAT IV 300V safety rated providing users with a rugged and water proof carry case for a full days work even in challenging environments.

Megger EVCA210-UK Electric Vehicle Charge Point Adaptor

The Megger EVCA210-UK Electric Vehicle Charge Point Adaptor is built to simulate the connection between an electrical vehicle and a charging point that is being tested. The EVCA210 adaptor using its intuitive interface can determine dangerous voltages that are present on the PE. Both Type 1 and Type 2 plugs are supplied with unit with Type 1 plugs for charging points with fixed cables and vehicles connectors and Type 2 plugs used for fixed cables with vehicle connectors air charging points featuring panel mounted socket outlets. This instrument boasts an input voltage of up to 250V in a single phase system, up to 430V in a three phase system and input frequency of 50/60Hz.

The EVCA210 incorporates front mounted mains sockets and 4mm connection ports (L1, L2, L3, N and PE) for performing measurements on live conductors whilst the two additional CP signal thermals so a technician can measure CP signal signal via an oscilloscope. The EVCA210 is IP54 rated offering protection from dust ingress and encased in a soft carry case. The CAT II 300V device conducts testing in accordance with IEC/EN 61851-1 and IEC/HD 60364-7-722 regulations. The unit is also compliant with Low Voltage Directive LVD 2014/35 and in line with EC/EN 61010-1:2010 and IEC/EN 61010-2-030:2010 safety standards.

Key Features

  • Designed for the electrical testing of single and 3-phase installations
  • Brand new features including full colour screen, RCD configurator and EV charge point testing
  • TrueLoop measurement using patented confidence meter
  • Fully compatible with CertSuite for easy certificate generation and reporting

  • Never be without power with our quick-remove battery pack and rechargeable battery option
  • Testing adaptor for Mode 3 Electric Vehicle charge points (AC)
  • EVSE tester capable of testing single and three phase EV charging points
  • Single phase system - Input voltage up to 250V
  • Three phase system - Input voltage up to 430V
  • Input frequency of 50/60Hz
  • Simulates the connection an Electric Vehicle to charging point
  • PE pre-test function
  • Button for CP Error “E” & PE Error (Earth Fault) simulation
  • Rotary dial provides PP State or CP state simulation
  • Suitable for an array of appliances with Type 2 & Type 1 charging plugs included
  • 4mm front mounted connection ports (L1, L2, L3, N and PE)
  • Two 4mm ports for connection to an oscilloscope
  • Lightweight & compact design
  • IP54 and CAT II 300V rated
  • In accordance with regulations - IEC/EN 61851-1 and IEC/HD 60364-7-722
  • In line with directive - LVD 2014/35
  • Compliant with safety standards - EC/EN 61010-1:2010 and IEC/EN 61010-2-030:2010
What's In The Box?

Megger MFT-X1 Multifunction Tester

  • Megger MFT-X1 Multifunction Tester
  • Switched test probe SP5
  • Red test lead, probes, clips and grabbers
  • Blue test lead, probe, clips and grabbers
  • Green test lead, probe, clips and grabbers
  • Li-ION battery 4400 mAh
  • Li-ION battery charger
  • SIA10 MAINS socket interface adaptor UK
  • Neck strap
  • Multipurpose hard base carry case
  • Quick start guide
  • Calibration certificate

Megger EVCA210-UK Electric Vehicle Charge Point Adaptor

  • Megger EVCA210-UK Electric Vehicle Charge Point Adaptor
  • Type 1 Charging Plug
  • Type 2 Charging Plug
  • 2x Connection Cables
  • EVCA210 Carry Case
  • Instruction Manual

Payment & Security

Payment methods

American Express Apple Pay Diners Club Discover Google Pay Maestro Mastercard PayPal Shop Pay Union Pay Visa

Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.


Shipping and Returns

-Standard delivery to UK mainland only £5.95 (3-5 days service). Restrictions Apply

- Some products may incur an additional £150 delivery charge where a palletised delivery is required.

You may also like

Recently viewed